Sunrise Systems LED Sign revisited

 I was asked to convert another Sunrise Systems LED sign to Arduino control and wireless updates via bluetooth.  This time I wanted to make the conversion simpler by reusing the driver IC's and Transistors.  To do that I cut the board in half just to the right of the processor.  Then I tapped into signals on the 74HC04 and 74HC138.  The following picture shows the location for the cut and where to tap into the signals:

Here is a picture of the prototypeing of this new setup.  Everything worked but some of the signals were inverted so it took some playing with the code to get it to work.

I spliced in a bare board to add the arduino processor. 

Here is the revised code for a basic version of this arrangement;

// Sunrise 7x96 Uno LED Array driver

// Easier to read code

// 4/4/2024 by Bob Davis

#define Data 7// Data pin

#define CLK 8 // Port B assignments 

#define OE  9 // 74138 pins 4 and 5

#define LAT 10// Latch

#define A0 11 // 74138 pin1

#define A1 12 // 74138 pin2

#define A2 13 // 74138 pin3

String text="ARDUINO+SUNRISE  ";

// This font from http://sunge.awardspace.com/glcd-sd/node4.html

byte font[][7] = {

0x00,0x00,0x00,0x00,0x00,0x00,0x00, // ascii 32

0x00,0x00,0xfa,0x00,0x00,0x00,0x00, // !

0x00,0xe0,0x00,0xe0,0x00,0x00,0x00, // "

0x28,0xfe,0x28,0xfe,0x28,0x00,0x00, // #

0x00,0x34,0xfe,0x58,0x00,0x00,0x00, // $

0xc4,0xc8,0x10,0x26,0x46,0x00,0x00, // %

0x6c,0x92,0xaa,0x44,0x0a,0x00,0x00, // &

0x00,0xa0,0xc0,0x00,0x00,0x00,0x00, // '

0x00,0x38,0x44,0x82,0x00,0x00,0x00, // (

0x00,0x82,0x44,0x38,0x00,0x00,0x00, // )

0x10,0x54,0x38,0x54,0x10,0x00,0x00, // *

0x10,0x10,0x7c,0x10,0x10,0x00,0x00, // +

0x00,0x0a,0x0c,0x00,0x00,0x00,0x00, // ,

0x10,0x10,0x10,0x10,0x10,0x00,0x00, // -

0x00,0x06,0x06,0x00,0x00,0x00,0x00, // .

0x04,0x08,0x10,0x20,0x40,0x00,0x00, // /

0x7c,0x8a,0x92,0xa2,0x7c,0x00,0x00, // 0

0x00,0x42,0xfe,0x02,0x00,0x00,0x00, // 1

0x42,0x86,0x8a,0x92,0x62,0x00,0x00, // 2

0x84,0x82,0xa2,0xd2,0x8c,0x00,0x00, // 3

0x18,0x28,0x48,0xfe,0x08,0x00,0x00, // 4

0xe4,0xa2,0xa2,0xa2,0x9c,0x00,0x00, // 5

0x3c,0x52,0x92,0x92,0x0c,0x00,0x00, // 6

0x80,0x8e,0x90,0xa0,0xc0,0x00,0x00, // 7

0x6c,0x92,0x92,0x92,0x6c,0x00,0x00, // 8

0x60,0x92,0x92,0x94,0x78,0x00,0x00, // 9

0x00,0x6c,0x6c,0x00,0x00,0x00,0x00, // :

0x00,0x6a,0x6c,0x00,0x00,0x00,0x00, // ;

0x00,0x10,0x28,0x44,0x82,0x00,0x00, // <

0x28,0x28,0x28,0x28,0x28,0x00,0x00, // =

0x82,0x44,0x28,0x10,0x00,0x00,0x00, // >

0x40,0x80,0x8a,0x90,0x60,0x00,0x00, // ?

0x4c,0x92,0x9e,0x82,0x7c,0x00,0x00, // @

0x7e,0x90,0x90,0x90,0x7e,0x00,0x00, // A

0xfe,0x92,0x92,0x92,0x6c,0x00,0x00, // B

0x7c,0x82,0x82,0x82,0x44,0x00,0x00, // C

0xfe,0x82,0x82,0x82,0x7c,0x00,0x00, // D

0xfe,0x92,0x92,0x92,0x82,0x00,0x00, // E

0xfe,0x90,0x90,0x80,0x80,0x00,0x00, // F

0x7c,0x82,0x82,0x8a,0x4c,0x00,0x00, // G

0xfe,0x10,0x10,0x10,0xfe,0x00,0x00, // H

0x00,0x82,0xfe,0x82,0x00,0x00,0x00, // I

0x04,0x02,0x82,0xfc,0x80,0x00,0x00, // J

0xfe,0x10,0x28,0x44,0x82,0x00,0x00, // K

0xfe,0x02,0x02,0x02,0x02,0x00,0x00, // L

0xfe,0x40,0x20,0x40,0xfe,0x00,0x00, // M

0xfe,0x20,0x10,0x08,0xfe,0x00,0x00, // N

0x7c,0x82,0x82,0x82,0x7c,0x00,0x00, // O

0xfe,0x90,0x90,0x90,0x60,0x00,0x00, // P

0x7c,0x82,0x8a,0x84,0x7a,0x00,0x00, // Q

0xfe,0x90,0x98,0x94,0x62,0x00,0x00, // R

0x62,0x92,0x92,0x92,0x8c,0x00,0x00, // S

0x80,0x80,0xfe,0x80,0x80,0x00,0x00, // T

0xfc,0x02,0x02,0x02,0xfc,0x00,0x00, // U

0xf8,0x04,0x02,0x04,0xf8,0x00,0x00, // V

0xfe,0x04,0x18,0x04,0xfe,0x00,0x00, // W

0xc6,0x28,0x10,0x28,0xc6,0x00,0x00, // X

0xc0,0x20,0x1e,0x20,0xc0,0x00,0x00, // Y

0x86,0x8a,0x92,0xa2,0xc2,0x00,0x00, // Z

};

void setup() {

  Serial.begin(9600);

  Serial.println("Arduino is ready");

  pinMode (Data, OUTPUT); // Data pin to output

  pinMode (CLK, OUTPUT);  // Clock pin to output

  pinMode (OE, OUTPUT);   // Out Enable pin to output

  pinMode (LAT, OUTPUT);  // Latch pin to output

  pinMode (A0, OUTPUT);   // Address pin to output

  pinMode (A1, OUTPUT);   // Address pin to output

  pinMode (A2, OUTPUT);   // Address pin to output

}

     

void loop() {

    if (Serial.available() > 0){

      text=Serial.readString();

      text.toUpperCase();

      Serial.print(text);

      }

    // Select the Row

    for (int r=0; r<8; r++){

      // select the character

      for (int ch=17; ch>-1; ch--){

        // select the column within character

        for (int c=5; c>-1; c--){

          digitalWrite(Data, HIGH); // Data is inverted!

          if ((font[text[ch]-32][c] >> r+1) & 0x01==1) digitalWrite(Data, LOW);

          digitalWrite(CLK, LOW);  // Toggle Clock

          digitalWrite(CLK, HIGH);

        }

      }

      // This row is done so display it

      digitalWrite(OE, HIGH);  // Turn off display

      digitalWrite(LAT, HIGH); // Latch  data

      digitalWrite(LAT, LOW); // Ready for next latch

      digitalWrite(A0, LOW);  // Update Row 

      digitalWrite(A1, LOW);

      digitalWrite(A2, LOW);

      if ((r & 0X01)==1) digitalWrite(A0, HIGH);

      if ((r & 0X02)==2) digitalWrite(A1, HIGH);

      if (r > 3) digitalWrite(A2, HIGH);

      digitalWrite(OE, LOW);  // Display back on

      }

    }